Whelen 9052001 Manuel d'utilisateur télécharger pdf

Page 1

ENGINEERING COMPANY INC.

3.74

MFG

LABEL

BLACK (-) GROUND

(28VDC) 18AWG 12” ±1.0”

(14VDC) 20AWG 6.0"±1.0"

WHITE (+) 28VDC

18AWG 12” ±1.0”

RED (+)14VDC

20AWG 6" ±1.0"

2.60

NOTE:

RED LEDs

TO THE FRONT

51 Winthrop Road

Chester, Connecticut 06412-0684

Phone: (860) 526-9504

Fax: (860) 526-2009

Internet: www.whelen.com

Sales/Service e-mail: [email protected]

Aviation

Installation Guide:

Model 90520( )-series

Model(s) 9052001, 9052051

P/N:01-0790520-01,

01-0790520-51

LED Flashing Split Anti-Collision

Light Assembly

Form No.14290A (012712)

OPERATING INSTRUCTIONS:

Operational Voltage: . . . . . . . . . . . 28 VDC nominal

Average Input Current: . . . . . . . . . 0.67 Amps

Pulse Input Current: . . . . . . . . . . . 3.0 Amps @ .3 Seconds

The Model 90520 series LED Flashing Split Anti-collision Light

Assembly meets the requirements of FAR 91.205(c)(3).

CONTINUED AIRWORTHINESS: The 90520 series LED Flashing Split

Anti-collision Light Assembly is designed with 4 vertical columns

consisting of 4 red LEDs each and 4 vertical columns consisting of 3

white LEDs each. Should any one LED or any vertical column fail, the

unit must be repaired or replaced. Inspect the lens and replace if there

is excessive scratching, discoloration or cracking.

INSTALLATION PROCEDURES: The following information is to assist

in the installation of a Whelen LED Flashing Split Anti-collision Light

System.

1. The installation procedure described in the following text will be

confined to a single light installation, but is identical for multiple

light installations.

2. Using the “suggested mounting hole pattern” prepare the aircraft

for means to secure the LED Flashing Split Anti-collision Light

Assembly. Remove any existing mounting adapters.

3. 28 VDC (+) and (-) ground leads equipped with an appropriate

sized breaker to be supplied to the LED Flashing Split Anti-

collision Light Assembly System. Both leads must be connected

by an approved FAA connection. Insure that the wire leads are

clear of any obstructions and ty-wrap as required.

4. Install the light assembly by first removing the lens. Remove the

adapter plate. Attach the adapter plate to the aircraft mounting

holes. Refer to page 2. Reinstall the light assembly and lens.

5. All inverted (bottom) mounted units shall require waterproofing of

the flasher base assembly to the aircraft. Note: Drill a 1/8” hole in

the center of the lens for bottom mount units.

6. Check all avionics systems for interference from this installation.

7. A flight check should be performed by a properly certified pilot.

8. Update aircraft records, complete Form 337 and obtain FAA field

approval for installation, as required.

TSO-C96a CLASS III

APPROVED

MADE IN THE U.S.A.

The conditions and tests required for TSO approval of this

article are minimum performance standards. It is the

responsibility of those installing this article either on or

within a specific type or class of aircraft to determine that

the aircraft installation conditions are within the TSO

standards. TSO articles must have separate approval for

installation in aircraft. The article may be installed only if

performed under 14 CFR part 43 or the applicable

airworthiness requirements.

1 2

Résumé du contenu

Page 1 - Aviation

Page 1®ENGINEERING COMPANY INC.3.74MFGLABELBLACK (-) GROUND(28VDC) 18AWG 12” ±1.0”(14VDC) 20AWG 6.0"±1.0"WHITE (+) 28VDC18AWG 12” ±1.0”RED (

Page 2 - ITEM PART NUMBER DESCRIPTION

Page 2114441114441ITEM PART NUMBER DESCRIPTIONMODEL 9052001 (IRIDITE / 28V)ADAPTER PLATE, 8-HOLEMODEL 9052051 (IRIDITE / 14V)ASSY, 28V LED ANTI COLLIS

Modèles reliés 9052051

Commentaires sur ces manuels

Pas de commentaire

Whelen 9052001 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Équipement aérien Whelen 9052001. Whelen 9052001 User Manual Manuel d'utilisatio

Résumé du contenu

Modèles reliés 9052051

Commentaires sur ces manuels

Produits connexes et manuels pour Équipement aérien Whelen 9052001