Whelen P36P1L Manuel d'utilisateur télécharger pdf

Page 1

ENGINEERING COMPANY INC.

51 Winthrop Road

Chester, Connecticut 06412-0684

Phone: (860) 526-9504

Fax: (860) 526-2009

Internet: www.whelen.com

Sales/Service e-mail: [email protected]

Aviation

STC Manual

Form No.14793 (070714)

INSTALLATION PROCEDURES: The following

information provides guidelines for the installation of

the Whelen LED PAR Lights listed above. Please refer

to the OEM manual for your aircraft for specific

removal and installation instructions.

1. Place the lighting switch in the OFF position.

2. Inspect the housing, attachment points and

retainer for any signs of abnormal wear or

damage.

3. Loosen or remove the hardware holding the

lamp in place. Take steps to ensure the retainer

doesn't fall from the lamp assembly before it is

ready to be removed.

4. Place retainer screws in a safe place.

5. Remove the lamp from the holder.

6. Note there are two wires connected to the

(existing) lamp. Using a multi-meter, identify the

negative wire by measuring continuity to ground.

Place a piece of black electrical tape around the

wire identified as ground. This is your negative

lead.

7. Identify the positive wire as the remaining wire

lead. The LED light assembly is polarity

sensitive, however you will not damage the unit

by reversing the polarity.

8. While holding the lamp, loosen the screws

holding the attached wires. Remove each wire

from the lamp.

9. Secure the LED Light, note the terminal

markings for positive and negative, attach the

MODEL LIST

Model Part # Style Application Weight* VDC* Input Current*

P36P1L 01-0771833-10 PAR36 Landing 0.52 lbs. 14VDC 1.36 Amps

P36P1T 01-0771833-15 PAR36 Taxi 0.52 lbs. 14VDC 1.36 Amps

P36P2L 01-0771833-20 PAR36 Landing 0.52 lbs. 28VDC 0.68 Amps

P36P2T 01-0771833-25 PAR36 Taxi 0.52 lbs. 28VDC 0.68 Amps

P46P1L 01-0790750-10 PAR46 Landing 1.00 lbs. 14VDC 2.60 Amps

P46P2L 01-0790750-20 PAR46 Landing 1.00 lbs. 28VDC 1.25 Amps

MADE IN THE U.S.A.

negative marked wire to the negative side

terminal post of the LED Light.

10. Attach the positive wire to the positive side

terminal post. Remove tape or temporary

placard which identified the polarity of the wiring

inside the housing.

11. If required, install the rubber gasket included

with your new LED Light around the LED Light

assembly. A light application of a common hand

soap on the rubber may aid in its fit into the light

housing.

12. Place the LED light into the housing ensuring

the key (of the assembly) matches the key of the

housing. Proper orientation of the lamp is

necessary for beam orientation to be left and

right of centerline while in operation. For a Taxi

light, the ‘lines’ of the inner optic should be

orientated vertically to produce a horizontal light

beam.

13. Secure the retainer. Care should be taken to

tighten the screw only to the point the retainer

does not turn with hand pressure. Over-

tightening may stress the polycarbonate lens of

the LED Light.

14. Place the light switch in the ON position and

verify proper operation of the Whelen LED lamp.

15. Update records in accordance with 14CFR

91.407. Determine that the landing or taxi light

characteristics have not been substantially

affected.

*NOMINAL

1 2 3 4 5

Résumé du contenu

Page 1 - Aviation

Page 1®ENGINEERING COMPANY INC.51 Winthrop RoadChester, Connecticut 06412-0684Phone: (860) 526-9504Fax: (860) 526-2009Internet: www.whelen.comSales/Se

Page 2 - (reference-only)

Page 2PAR46(reference-only)PAR36(reference-only)WWW. .COMRGNDPolarity shownon label+VDCWWW.+14V+14VGND.COMRPolarity shownon labelAlignmentKeyAlignment

Page 3 - Periodic Inspections

Page 3Periodic InspectionsINTERVAL DESCRIPTION ACTIONS NOTES50 Hours • Perform function check. Observe that all LEDs are illuminated.Note: To reduce e

Page 4

Page 4WWW.+14VGND.COMRExistingGroundWireExistingLanding/Taxi LightSwitchExistingAircraft(+) VDCExistingFuse orCircuit BreakerTroubleshooting Procedure

Page 5 - ITEM PART NUMBER DESCRIPTION

Page 52321ITEM PART NUMBER DESCRIPTIONREPLACEMENT PARTS:PAR36 (All Models)LENS, CLEAR NON OPTIC PAR-36SCREW, 4 X 3/8 PFH PLASTI-LOC SS W/NYSEALSCREW,

Modèles reliés P36P1T | P36P2L | P36P2T | P46P1L | P46P2L |

Commentaires sur ces manuels

Pas de commentaire

Whelen P36P1L Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Équipement aérien Whelen P36P1L. Whelen P36P1L User Manual Manuel d'utilisatio

Résumé du contenu

Modèles reliés P36P1T | P36P2L | P36P2T | P46P1L | P46P2L |

Commentaires sur ces manuels