Whelen 70A02SAR Manuel d'utilisateur télécharger pdf (Page 2)

Page 2

3.281"

2.375"

1.187"

6.562"

1" diameter hole

1/4" mounting hole

(4 places)

Installation:

IMPORTANT! It is the responsibility of the installation technician to make sure

that the installation and operation of this product will not interfere with or

compromise the operation or efficiency of any vehicle equipment!

4. Position the lighthead onto the mounting surface and secure to the vehicle

using the four supplied #6 x 1-1/2” sheet metal screws.

Wiring:

WARNING! All customer supplied wires that connect to the positive terminal

of the battery must be sized to supply at least 125% of the maximum operating

current and FUSED

at the battery to carry that load. DO NOT USE CIRCUIT

BREAKERS WITH THIS PRODUCT!

The 700 Series lighthead offers the user various features depending on the model.

Refer to the next page for wire designations and replacement parts.

Scan-Lock™ (White/Violet):

Note that the lighthead must be on to use the Scan-Lock™ feature except

where noted.

To advance to the next flash pattern - Apply +12VDC to the WHT/VIO wire for less

than 1 second and release.

To cycle backwards through the flash patterns - Apply +12VDC to the WHT/VIO

wire for more than 1 second and release.

To reset to the factory default flash pattern - Turn off power to the lighthead. While

applying +12VDC to the WHT/VIO wire, turn power to the lighthead on. Continue to

apply voltage to the WHT/VIO wire for 5 seconds. The default pattern will now be

active.

NOTE: A Normally Open momentary switch is suggested to activate the Scan-

Lock™ wire.

SYNC (Grey) - To SYNC two lightheads, configure both lightheads to display the

same Phase 1 pattern. With the power off, connect the Grey wires from each

lighthead. When the lightheads are activated, their patterns will be synchronized. To

configure the two lightheads to alternate their patterns, advance the pattern of either

lighthead to the Phase 2 mode of the current pattern. Remember, Phase 1 patterns

ALWAYS

alternate with Phase 2 patterns!

Hi/Low Intensity (Violet) - This feature allows the user to step the unit down to low

power operation for nighttime use. Apply positive voltage to the VIOLET wire to put

the lighthead into low power. Remove the voltage from the VIOLET wire to restore

normal high power operation.

The table below provides wiring information for the 700 Series lighthead. Refer to the

appropriate flash pattern list as determined by the lighthead style:

WARNING! The LED models designated “Steady” must be connected to an

electronic flasher. Allowing the LED to steady burn will damage the lighthead

and void the warranty.

This product draws significantly less current than a

standard incandescent automotive bulb. If your flasher does not operate

properly, it may be necessary to replace your existing flasher module with a

Whelen 3TERM flasher module. Contact your sales representative for specific

vehicle application.

Caution: Permanent mounting of this product will require drilling. It is

absolutely necessary to make sure that no other vehicle components could be

damaged by this process. Check both sides of the mounting surface before

starting. If damage is likely, select a different mounting location.

1. Using the dimensions shown, mark off and drill the four 1/4” diameter mounting

holes and the 1” wire hole into the mounting surface. Check measurements

before drilling.

2. Install the flange grommet into the mounting holes then install a rubber

grommet (customer supplied) into the wire hole.

3. Using appropriately sized wires (minimum 18 AWG wire), extend the lighthead

wires to their appropriate connections. Fuse the positive connections at 3

Amps and test operation of lighthead before securing it to vehicle.

1. SignalAlert™ 75 - ALT

2. SignalAlert 75 - SIM

3. CometFlash 75 - ALT

4. CometFlash 75 - ALT

5. DoubleFlash 75 - ALT*

6. DoubleFlash 75 - SIM*

7. SingleFlash 75 - ALT*

8. SingleFlash 75 - ALT*

9. ComAlert™ 75 - ALT

10. ComAlert 75 - SIM

11. LongBurst™ 75 - ALT

12. LongBurst 75 - SIM

13. PingPong™ 75 - ALT*

14. PingPong 75 - SIM*

15. SSNF 75

16. SingleFlash 60 - ALT

17. SingleFlash 60 - SIM

18. SingleFlash 90 - ALT*

19. SingleFlash 90 - SIM*

20. SingleFlash 120 - ALT*

21. SingleFlash 120 - SIM*

22. SingleFlash 300 - ALT

23. SingleFlash 300 - SIM

24. DoubleFlash 150 - ALT

25. DoubleFlash 150 - SIM

26. ComAlert™ 150 - ALT

27. ComAlert 150 - SIM

28. ActionFlash™ - ALT 50

29. ActionFlash™ - SIM 50

30. ActionFlash™ - ALT 150

31. ActionFlash™ - SIM 150

32. ModuFlash™ - ALT

33. ModuFlash™ - SIM

34. DoubleFlash - ALT 120*

35. DoubleFlash - SIM 120*

36. PingPong™ - ALT 120*

37. PingPong™ - SIM 120*

38. TripleFlash™ - ALT 75*

39. TripleFlash™ - SIM 75*

40. TripleFlash™ 120 - ALT*

41. TripleFlash™ 120 - SIM*

42. SignalAlert CAL - ALT*

43. SignalAlert SIM - ALT*

44. ActionFlash™/SingleFlash

60/120 - ALT*

45. ActionFlash™/SingleFlash

60/120 - SIM*

46. ActionFlash™/SingleFlash

120/TF75 - ALT*

47. ActionFlash™/SingleFlash

120/TF75 - SIM*

48. CalScan™ - ALT + SIM*

49. ActionScan™ - ALT + SIM

50. SteadyFlash 60*

51. SteadyFlash 75*

52. SteadyFlash 90*

53. SteadyFlash 120*

54. Steady / Steady*

* = California Title XIII compliant

1. SignalAlert™75

2. SignalAlert150

3. SingleFlash 375

4. SingleFlash 150

5. SingleFlash 75*

6. DoubleFlash 150

7. DoubleFlash 75*

8. CometFlash®75

9. ActionFlash

10. ModuFlash

11. ComAlert

12. ActionScan

13. SignalAlert

14. Steady

* = California Title XIII compliant

Sync-Capable Flash Patterns:

1. SignalAlert™ 75 - Phase 1

2. SignalAlert 75 - Phase 2

3. CometFlash® 75 - Phase 1

4. CometFlash 75 - Phase 2

5. DoubleFlash 75 - Phase 1

6. DoubleFlash 75 - Phase 2

7. SingleFlash 75 - Phase 1

8. SingleFlash 75 - Phase 2

9. ComAlert™ 75 - Phase 1

10. ComAlert 75 - Phase 2

11. LongBurst™ 75 - Phase 1

12. LongBurst 75 - Phase 2

13. PingPong™ 75 - Phase 1

14. PingPong 75 - Phase 2

Non-Sync Flash Patterns:

15. SingleFlash 60*

16. SingleFlash 90*

17. SingleFlash 120*

18. SingleFlash 300

19. DoubleFlash 150

20. ComAlert 150

21. ActionFlash™ 50

22. ActionFlash 150

23. ModuFlash™

24. ActionScan™

25. Steady

* = California Title XIII compliant

Split Pattern Table:

Standard Pattern Table:

SYNC Pattern Table:

CAUTION! DO NOT LOOK DIRECTLY AT THESE LED’S WHILE THEY ARE ON.

MOMENTARY BLINDNESS AND/OR EYE DAMAGE COULD RESULT !

IMPORTANT WARNING!

IMPORTANT! Before returning the vehicle to active service, visually confirm the proper operation of this product, as well as all vehicle

components/equipment.

SCREW, 6 X 1-1/2" PPHSMS SS

GASKET

FLANGE GROMMET

700 SERIES

1/4" MOUNTING HOLE (4)

1 2 3

Commentaires sur ces manuels

Pas de commentaire

Whelen 70A02SAR Manuel d'utilisateur Page 2

Commentaires sur ces manuels

Produits connexes et manuels pour Pour la voiture Whelen 70A02SAR