Page 1
©2007 Whelen Engineering Company Inc.
Form No.14124B (011712)
Installation Guide:
SA315 Siren Speaker Bracket
2004-2012 Ford Escape
ENGINEERING COMPANY INC.
Internet: www.whelen.com
Canadian Sales e-mail: autocan@whelen.com
For warranty information regarding this product, visit www.whelen.com/warranty
51 Winthrop Road,
Chester, Connecticut 06412-0684
Phone: (860) 526-9504
Fax: (860) 526-4078
Automotive: Sirens & Switches
Protrusion on frame
Mount bracket
flush with frame here.
Hole in
bracket
1/4 X 1" Self-Drilling Hex Washer Screw HD
(Qty 5)
Slip the bracket (with siren attached) onto the frame. The square hole in the
top of the bracket will fit over the protrusion in the frame.
frame frame
frame
side view
Front Bumper Assembly Trim some plastic off of front bumper
assembly to fit siren.
Fig. 1
Fig. 2
Fig. 3
Installation:
1. Mount speaker to bracket (see next page).
2. Remove the one piece front bumper assembly from the vehicle
(Fig. 1). Refer to the vehicle factory manual for the removal
procedure.
3. Slip the bracket (with siren) onto the center of the lower frame of
the vehicle. There is a square hole in the top of the bracket that
fits over a small protrusion on the top of the frame (Fig. 2).
4. Secure the bracket to the frame with the supplied self tapping
screws. You will need a drill equipped with a 3/8” socket to drive
the screws in. Do not over tighten.
5. Replace the front bumper assembly. You will have to trim some
plastic off of the bumper assembly to make the siren fit properly.
6. Extend the WHITE (positive) and BLACK (negative) speaker
wires to your
siren amplifier
and connect as
shown in the
amplifiers
instructions.
CAUTION
Loud siren noise can cause
hearing damage and/or loss.
Refer to OSHA Section 1910.95 prior
to putting ANY siren into service!
Wear
Protection!
ACTIVATION OF THIS
SIREN MAY DAMAGE
UNPROTECTED EARS!
©2007 Whelen Engineering Company Inc.
Form No.14124B (011712)
Installation Guide:
SA315 Siren Speaker Bracket
2004-2012 Ford Escape
ENGINEERING COMPANY INC.
Internet: www.whelen.com
Canadian Sales e-mail: autocan@whelen.com
For warranty information regarding this product, visit www.whelen.com/warranty
51 Winthrop Road,
Chester, Connecticut 06412-0684
Phone: (860) 526-9504
Fax: (860) 526-4078
Automotive: Sirens & Switches
Protrusion on frame
Mount bracket
flush with frame here.
Hole in
bracket
1/4 X 1" Self-Drilling Hex Washer Screw HD
(Qty 5)
Slip the bracket (with siren attached) onto the frame. The square hole in the
top of the bracket will fit over the protrusion in the frame.
frame frame
frame
side view
Front Bumper Assembly Trim some plastic off of front bumper
assembly to fit siren.
Fig. 1
Fig. 2
Fig. 3
Installation:
1. Mount speaker to bracket (see next page).
2. Remove the one piece front bumper assembly from the vehicle
(Fig. 1). Refer to the vehicle factory manual for the removal
procedure.
3. Slip the bracket (with siren) onto the center of the lower frame of
the vehicle. There is a square hole in the top of the bracket that
fits over a small protrusion on the top of the frame (Fig. 2).
4. Secure the bracket to the frame with the supplied self tapping
screws. You will need a drill equipped with a 3/8” socket to drive
the screws in. Do not over tighten.
5. Replace the front bumper assembly. You will have to trim some
plastic off of the bumper assembly to make the siren fit properly.
6. Extend the WHITE (positive) and BLACK (negative) speaker
wires to your
siren amplifier
and connect as
shown in the
amplifiers
instructions.
CAUTION
Loud siren noise can cause
hearing damage and/or loss.
Refer to OSHA Section 1910.95 prior
to putting ANY siren into service!
Wear
Protection!
ACTIVATION OF THIS
SIREN MAY DAMAGE
UNPROTECTED EARS!
(2 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels