Whelen 9037701 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Équipement aérien Whelen 9037701. Whelen 9037701 User Manual Manuel d'utilisatio

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 2
  • Table des matières
  • MARQUE LIVRES
  • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 0
Page 1
5.69
1.87
1.08
.618 MIN
RED(+14VDC)
BLACK(-)GROUND
1.25 DIA
Tail Light Wires
(14V Versions Only)
WHITE (+28VDC) OR RED (+14VDC)
BLACK (-) GROUND
The conditions and tests required for TSO approval of this
article are minimum performance standards. It is the
responsibility of those installing this article either on or
within a specific type or class of aircraft to determine that
the aircraft installation conditions are within the TSO
standards. TSO articles must have separate approval for
installation in aircraft. The article may be installed only if
performed under 14 CFR part 43 or the applicable
airworthiness requirements.
®
ENGINEERING COMPANY INC.
Route 145, Winthrop Road,
Chester, Connecticut 06412
Phone: (860) 526-9504
Fax: (860) 526-2009
Internet: www.whelen.com
Sales/Service e-mail: aviation@whelen.com
Aviation
Installation Guide:
90377( )-series
Models 9037701 - 9037704
P/N: 01-0790377-01 through -04
LED Position Light Assembly
©2007 Whelen Engineering Company Inc.
Form No.14142 (091307)
POSITION LIGHT:
Operational Voltage:. . . . . . . . . . 14/28 VDC (nominal)
Input Current: . . . . . . . . . . . . . . . 0.5 / 0.25 Amps
EQUIPMENT LIMITATIONS: An approved lighting
system consists of two lights, one located on each
wingtip. The baseplate must be mounted parallel to the
vertical and horizontal centerlines of the aircraft to project
the patterns properly.
CONTINUED AIRWORTHINESS: The 90377 series
LED wingtip position light assembly is designed with 3
forward LED’s and two aft LED’s. If any one LED fails,
the unit must be repaired or replaced. Inspect the lens.
Replace if there is excessive scratching, discoloration or
cracking.
INSTALLATION PROCEDURES: The following
information is to assist in the installation of a Whelen
90377 Light System.
1. Choose the appropriate 90377( ) series
replacement light assembly.
2. The installation procedure described in the following
text will be confined to a single light installation, but
is identical for multiple light installations.
3. Remove the old light, locate and save the existing
+VDC lead and (-) ground lead. Clean and prep
ends as required.
4. Make sure the existing system is equipped with an
appropriate sized breaker. Connect the existing
+14/28 VDC lead to the POSITIVE wire on the input
cable assembly (supplied with the light assembly).
Connect the existing ground lead to the GROUND
wire on the input cable assembly or use the
supplied connector as shown in the illustrations.
Both leads must be connected by an approved FAA
connection. Insure that the wire leads clear of any
obstructions and ty-wrap as required.
5. Remove the shroud from the light assembly.
6. Position the base of the new light assembly onto the mounting
surface. Insert three (3) #6-32 pan head screws into the
mounting hole and tighten firmly. Reinstall the lens so that the
two notches are positioned under the shroud, with each notch
equadistant to the centerline.
7. Check all avionics systems for interference from the
installation.
8. A flight check should be performed by a properly certified
pilot.
9. Update aircraft records, complete Form 337 and obtain FAA
field approval for installation, as required.
MADE IN THE U.S.A.
TSO-C30c TYPES I, II, III
APPROVED
Vue de la page 0
1 2

Résumé du contenu

Page 1 - Aviation

Page 15.691.871.08.618 MINRED(+14VDC)BLACK(-)GROUND1.25 DIATail Light Wires(14V Versions Only)WHITE (+28VDC) OR RED (+14VDC)BLACK (-) GROUNDThe condit

Page 2 - 28V VIEW

Page 2111061298734501-0290378-0201-0290378-0401-0790376-0401-0790376-0368-3950903A3068-3950902A3038-0250901-0001-0290378-0301-0790376-02*QTY. QTY. QTY

Modèles reliés 9037702 | 9037703 | 9037704 |

Commentaires sur ces manuels

Pas de commentaire