Whelen OR650PGE Manuel d'utilisateur télécharger pdf

Page 1

ENGINEERING COMPANY INC.

3.85

1.92

(REF)

6.0” ± 1.0”

(20 AWG,

MIL-22759/43)

AMP 350780-1

Connector

(w/Contact

AMP 350547-1)

.67

WIRING CHART

White 28VDC ACL Pos. 3

Orange 28VDC POS Pos. 1

Yellow SYNC Pos. 4

Black Ground Pos. 2

1.67

.500

SUGGESTED MOUNTING DETAIL

1.340

Area

To Be

Removed

2.500

.740

.630

.670

1.000

51 Winthrop Road

Chester, Connecticut 06412-0684

Phone: (860) 526-9504

Fax: (860) 526-2009

Internet: www.whelen.com

Sales/Service e-mail: [email protected]

Aviation

Installation Guide:

Aviation model(s) OR650PGE, OR650PRE

P/N 01-0790701-P1, 01-0790701-P2

Orion 650E

Wingtip Position/Anti-Collision Lighthead

Form No.14744A (072214)

SPECIFICATIONS:

Nominal Operational Voltage: ......................... 28VDC

(Operational from 22-32 VDC)

Input Current:

Position Lights................................................. 0.15 Amps

Anti-Collision Light (Avg.)................................ 0.35 Amps

Anti-Collision Light (Pulse) .............................. 1.8 Amps

Flashrate ......................................................... 45 ± 5 FPM

EQUIPMENT LIMITATIONS:

An approved forward position lighting system consists of three lights,

one located on the tail and one located on each wingtip. Model

OR650( )E is a wingtip position and anti-collision light.The assembly

should be mounted as far outboard on the aircraft as practical. The

baseplate must be mounted parallel to the vertical and horizontal

centerlines of the aircraft to project the patterns properly. This

assembly must be mounted behind a clear lens.

Certain types of installations may require additional testing.

CONTINUED AIRWORTHINESS:

The forward position light is designed with green or red LEDs. The

anti-collision light is designed with 24 white LEDs. If any one LED fails,

the unit must be repaired or replaced.

Note: To reduce eye strain, use an optical filter such as dark glasses

or a blue covering dome during LED inspection.

INSTALLATION PROCEDURES:

The following information is to assist you in installing a Whelen light

system.

1. Choose the appropriate light assembly.

2. Using the mounting detail information provided, prepare the

aircraft for means to secure the light assembly.

3. Carefully remove the #4 phillips head screw (qty. 4). Remove the

light assembly from the baseplate. CAUTION! Do not touch the

LED with either fingers or sharp objects. This could soil and/

or damage the lens and affect the optical performance of the

LEDs.

4. Using the appropriate hardware install the baseplate to the

aircraft.

5. Route the wires through the opening in the baseplate. Connect

the light inputs according to the chart shown. Connect the power

lead to an appropriately sized breaker. Connections to be

according to FAA approved methods.

Note: SYNC is a low-power, bi-directional control signal.

Connecting to the synchronize signal of any Whelen LED anti-

collision assembly to another Whelen anti-collision assembly will

cause the lights to flash at the same time. If Synchronization is

not necessary, the connection may be left open.

6. Re-install the light assembly on to the baseplate and insure that

all leads are clear of any obstructions and secured as required.

7. Check all avionics systems for interference from this installation.

8. A flight check should be performed by a properly certified pilot.

9. Update aircraft records, complete Form 337 and obtain FAA field

approval for installation, if required.

MADE IN THE U.S.A.

The conditions and tests required for TSO approval of this article are minimum

performance standards. It is the responsibility of those installing this article either on

or within a specific type or class of aircraft to determine that the aircraft installation

conditions are within the TSO standards. TSO articles must have separate approval

for installation in aircraft. The article may be installed only if performed under 14 CFR

part 43 or the applicable airworthiness requirements.

TSO-C30c

TYPE I & II;

APPROVED

TSO-C96a

CLASS II;

APPROVED

1 2

Aviation 1
07-771791-R10 shown 2

Résumé du contenu

Page 1 - Aviation

Page 1®ENGINEERING COMPANY INC.3.851.92(REF)6.0” ± 1.0”(20 AWG,MIL-22759/43)AMP 350780-1Connector(w/ContactAMP 350547-1).67WIRING CHARTWhite 28VDC ACL

Page 2 - 07-771791-R10 shown

Page 21207-771791-R10 shownfor reference only345--1ITEM PART NUMBER DESCRIPTIONOR6502PRE Wingtip Position/Anti-Collision Light, 28V (Red)OR6502PGE Win

Modèles reliés OR650PRE

Commentaires sur ces manuels

Pas de commentaire

Whelen OR650PGE Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Équipement aérien Whelen OR650PGE. Whelen OR650PGE User Manual Manuel d'utilisatio

Résumé du contenu

Modèles reliés OR650PRE

Commentaires sur ces manuels

Produits connexes et manuels pour Équipement aérien Whelen OR650PGE