Whelen 9032501 Manuel d'utilisateur télécharger pdf

Page 1

.34

(4.6)

10.24

REF. 1.2

24.0" ± 1.0

2.93

2.61

REF. 1.2

20 AWG 22759/34 WIRES

RF SHIELDED

ABRASION RESISTANT JACKET

MS3476L12-10P

ENGINEERING COMPANY INC.

Route 145, Winthrop Road,

Chester, Connecticut 06412

Phone: (860) 526-9504

Fax: (860) 526-2009

Internet: www.whelen.com

Sales/Service e-mail: aviation@whelen.com

Aviation

Installation Guide:

Aviation model 9032501,9032502

P/N 01-0790325-01, 01-0790325-02

LED Anti-Collision/LED Position Light Ass’y

Form No.14136 (082907)

SPECIFICATIONS:

Nominal Operational Voltage:........ 28 VDC

Total Weight .................................... 1.2 lbs.

EQUIPMENT LIMITATIONS:

An approved Anti-Collision / Position System consists

of assembly 90325( ) and flasher 7112000, located on

each wingtip.

CONTINUED AIRWORTHINESS:

The forward position light is designed with 6 LED’s. The

rear position light is designed with 3 LED’s. The Anti-

Collision light is designed with 36 LED’s. If any one LED

fails, the lighthead module must be repaired or

replaced. Inspect the lens for excessive scratches or

pitting. Replace if necessary.

Note: The anti-collision light will automatically shut-off

after 9-10 flashes if a failure is detected.

INSTALLATION PROCEDURES:

The following information is to assist you in installing a

Whelen Anti-Collision / Position light system.

1. Choose the appropriate Model 90325 - ( )

replacement light assembly.

2. The installation procedure described in the

following text will be confined to a single light

installation, but is identical for multiple light

installation.

3. Using #6 flathead screws, install light assembly

and insure that all leads are clear of any

obstructions and ty-rap as required. Secure light

assembly, using vibration resistant threaded

fasteners.

4. Connect the MS connector to flasher/current

source model 7112000.

5. Check all avionics systems for interference from

this installation.

6. A flight check should be performed by a properly

certified pilot.

7. When necessary, waterproof the light base to

aircraft. Apply single part silicone (RTV) or

equivalent around any open area where water

could get in.

8. Update aircraft records and complete Form 337, as

necessary.

9. Obtain FAA field approval for installation, as

necessary.

MADE IN THE U.S.A.

The conditions and tests required for TSO approval of this

article are minimum performance standards. It is the

responsibility of those installing this article either on or

within a specific type or class of aircraft to determine that

the aircraft installation conditions are within the TSO

standards. TSO articles must have separate approval for

installation in aircraft. The article may be installed only if

performed under 14 CFR part 43 or the applicable

airworthiness requirements.

TSO-C30c

TYPES I , II & III

APPROVED

TSO-C96a

CLASS II

1 2

Aviation 1
(4 PLACES) 2

Résumé du contenu

Page 1 - Aviation

Page 1.34(4.6)10.24REF. 1.224.0" ± 1.02.932.61REF. 1.220 AWG 22759/34 WIRESRF SHIELDEDABRASION RESISTANT JACKETMS3476L12-10P®ENGINEERING COMPANY

Page 2 - (4 PLACES)

Page 223111ITEM PART NUMBER DESCRIPTIONASS'Y, GREEN LED FINAL MODEL 9032501ASS'Y, RED LED FINAL MODEL 9032502BASE, WINGTIP LT BLK POWDER CTA

Modèles reliés 9032502

Commentaires sur ces manuels

Pas de commentaire

Whelen 9032501 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Équipement aérien Whelen 9032501. Whelen 9032501 User Manual Manuel d'utilisatio

Résumé du contenu

Modèles reliés 9032502

Commentaires sur ces manuels

Produits connexes et manuels pour Équipement aérien Whelen 9032501